Components by Type
Shop by what the part does, not what industry uses it.
Engineers and architects often think in component families — pile, bulb, endcap, idler, hinge — and cross-shop those families across applications. This hub indexes the full SB5 catalog by product type so you can find the matching SKU regardless of which industry tag it carries.
Jump to a family
- Pile Weatherstrip3
- Brush Seals8
- Brush with Aluminum Holder1
- Rubber & EPDM Bulb Seals6
- Foam-Filled & Kerf-In Seals1
- Felt & Dust Seals1
- Thresholds2
- Endcaps3
- Idlers & Mounting3
- Roller Tubes & Bars2
- Motor Hardware2
- Hinges10
- Rollers4
- Bearings & Bearing Plates3
- Brackets & Fasteners7
- Window Operators2
- Sash Balances3
- Locks & Latches8
- Screen Frame Components3
- Glazing Components3
- Spring & Counterbalance Hardware5
- Hurricane / HVHZ Shutter Hardware2
- Awning Hardware6
- Commercial Door Hardware6
- Coil & Tape Products1
Pile Weatherstrip
UV-stabilized polypropylene pile in the full AAMA 701/702-23 dimensional matrix — T-slot, ribbed-back, adhesive-back, and finseal constructions.
Pile Weatherstrip
Polypropylene pile weatherstrip for fenestration, shading, and access system applications. Available in a wide range of pile heights and backing widths to fit any track or channel profile. Custom lengths and densities available.
View productAdhesive-Back Pile Weatherstrip
Self-adhesive pile weatherstrip for retrofit screens and any application without an integrated T-slot. UV-stable acrylic PSA holds across the screen service temperature range, and standard rolls in 17, 50, 100, and 250 ft lengths reduce waste on smaller production runs.
View productWindow Pile
Fine-denier pile weatherstrip specifically designed for window sash tracks and sliding window/door channels. Precision-sized for standard fenestration track profiles.
View product
Brush Seals
Brush seals in T-slot, fin-back, membrane-backed, and large-format profiles. Nylon and polypropylene filament, sized for screens, dock seals, industrial enclosures, and overhead doors.
T-Slot Brush Seal
Industrial brush seal with rigid T-slot or snap-in carrier for guide track channels, side rails, and housing extrusions. Slides or snaps directly into aluminum T-slot channels. Available in standard and high-density filament options.
View productBrush with Fin Seal
Combination brush and fin seal for enhanced air and light blocking. The rigid center fin provides a true weather seal while the surrounding pile filaments fill gaps and reduce vibration.
View productBrush + Membrane Seal
Heavy-duty brush seal with integrated rubber membrane backing for maximum sealing performance. Used in overhead door bottoms, loading dock seals, and industrial enclosure perimeters.
View productLarge-Format Brush Seal
Extra-wide brush seals for bottom bars, weight bars, and industrial applications requiring extended pile reach. Available with 12.5mm and 12.8mm wide carriers for heavy-duty mounting.
View productLintel Header Brush
Brush seal for overhead door lintels and header jambs. Seals the gap between the door curtain and the structural lintel to prevent drafts and pest entry.
View productHigh Bay Brush
Heavy-duty brush seals for industrial high bay doors, warehouse entrances, and loading dock openings. Oversized profiles for maximum gap coverage.
View productBottom Bar Brush
Brush seal designed for the bottom hem bar of motorized screens and roll shutters. Provides insect and light blocking at the bottom seal point while allowing smooth operation. Available with 12.5mm or 12.8mm backing widths.
View productFur Strip
Continuous fur strip for acoustic damping, dust sealing, and light blocking in shading housings, commercial doors, and residential applications. Available with 12.5mm or 12.8mm backing widths for motorized screen channels. Sold in bulk spools.
View product
Brush with Aluminum Holder
Nylon or polypropylene brush filament captured in a 6063-T5 aluminum extruded holder — for door perimeters, garage door side seals, and commercial door bottom sweeps.
Rubber & EPDM Bulb Seals
Hollow bulb extrusions in EPDM, TPV, silicone, and flexible PVC. P-bulb, D-bulb, round-bulb, T-end astragal, and threshold profiles for fenestration, shading, garage doors, and commercial doors.
Rubber Bulb Seal
EPDM rubber bulb seal profiles for weather sealing doors, windows, and enclosures. Available in D-profile, P-profile, hollow bulb, and kerf-mounted configurations. Custom extrusion profiles available.
View productEPDM Bulb Seal — Motorized Screen
EPDM bulb seal for motorized retractable screen housings and side rails. P-profile, D-profile, and hollow round bulbs in 6, 12, and 20 mm OD with grip stems sized for standard T-slot retention. Closed-cell EPDM for UV and ozone resistance, ASTM D2000 M2BG/M3BG compounded.
View productHood Weather Seal
Specialized rubber seal for motorized screen and shutter housing cassettes. Seals the gap between the headbox and the mounting surface to prevent water and insect intrusion.
View productT-End Bottom Astragal
Industry-standard T-end bottom astragal seal for sectional garage doors. Single-T and double-T stem widths (¼", 5/16"), flat sections from 2½" to 4½", and door-width lengths from 8 ft through 20 ft. Available in EPDM rubber for cold-weather flex, TPV for chemical resistance, or flexible PVC vinyl. Compounded to ASTM D2000 and tested as part of door systems meeting ANSI/DASMA 105 and 112 air-infiltration and leakage thresholds.
View productP-Bulb / Tube Garage Door Seal
P-bulb, round-bulb, and tube bottom seals for sectional garage doors with retainer-mounted profiles. ½", 1", and 1½" bulb diameters in EPDM, TPV, or flexible PVC, supplied in 10, 16.4, 18, and 20 ft door-width lengths. ASTM D2000 / ANSI-DASMA 105 verified.
View productEPDM Bottom Bar Bulb Seal — Shutters
EPDM, TPV, or flexible PVC bottom-bar bulb seal for rolling shutter assemblies. 12–25 mm bulb OD with 4–8 mm T-stem retention. Supplied in 10–250 ft coils. ASTM D2000, D1056, and E283 verified for compression and air infiltration.
View product
Foam-Filled & Kerf-In Seals
Kerf-in jamb seals with PU foam core, PE skin, and rigid PP spine. AAMA 702 / BHMA A156.22 compliant for door and window perimeter sealing.
Felt & Dust Seals
Felt and synthetic-fiber dust seals for fenestration tracks, light-gap closures, and acoustic sealing applications.
Thresholds
Saddle, ramped, and inserted threshold extrusions in aluminum 6063-T5 or heavy vinyl / EPDM for residential and commercial door openings.
Residential Garage Door Threshold Seal
Floor-mounted threshold seal for residential garage doors. Heavy-vinyl or EPDM extrusion in ½" to 1¼" heights and 3½" to 5½" widths, supplied in 8, 10, 16, and 20 ft lengths. Pairs with the door bottom astragal to close the threshold gap on uneven slabs.
View productSaddle Threshold
Aluminum 6063-T5 saddle threshold for commercial door openings. 3" to 6" widths; 1/4" to 1" heights. Mill, clear-anodized, or dark-bronze finishes. BHMA A156.21 and ADA/ANSI A117.1 compliant.
View product
Endcaps
Aluminum and glass-filled-nylon endcaps for roller tubes, motorized screen housings, and retractable awning cassettes. Bearing-supported idler variants for non-driven tube ends.
Aluminum Endcaps
Cast or extruded aluminum endcaps (6063-T5) for motorized screen housings, roller tubes, and retractable awning cassettes. Two categories: internal roller tube endcaps that insert into the tube bore, and external housing/cassette endcaps (side plates) that cap the protective hood box. Powder-coated for UV and corrosion resistance.
View productIdler End Cap with Bearing
Bearing-supported idler end cap for 40, 45, 52, 60, 70, 78, and 85 mm octagonal roller tubes used in motorized retractable screens and awnings. Glass-filled nylon body with ABEC-1 or ABEC-3 ball bearing on 10, 12, or 13 mm square axles. Collapsible variants available so tubes can be removed without dismounting the bracket.
View productHem Bar Endcap
Push-fit or screw-mount endcap for aluminum hem bar extrusions. Closes off the open end of the hem bar and locates the weight rod insert. ABS, PP, or nylon 6/6 construction; color-matched to common bar finishes.
View product
Idlers & Mounting
Free-end idler assemblies, mounting plates, and pre-assembled roller-idler combinations for motorized screen and awning systems.
Adjustable Idler
Adjustable spring-loaded idler assemblies for motorized screen and awning roller tubes. Available in single and double configurations for standard and heavy-duty applications.
View productIdler Mounting Plate
Steel mounting plates for securing idler assemblies to wall or soffit surfaces. Available in multiple sizes and configurations to match different housing profiles.
View productRoller Idler Assembly
Complete roller idler assemblies with bearings for smooth operation in screen and shutter systems. Pre-assembled and tested.
View product
Roller Tubes & Bars
Aluminum 6063-T5 roller tubes up to 7 m with internal keying, and hem-bar extrusions for screen and awning systems.
Aluminum Roller Tube
Precision-drawn aluminum tubes for screen and awning roller systems. Available in standard diameters or custom profiles with internal keying.
View productAluminum Hem Bar (Bottom Bar)
Bottom hem bar extrusion for motorized retractable screen and awning systems. Adds weight to the bottom edge of the fabric for clean retraction and tensioning. Aluminum 6063-T5 in 25×40 mm to 50×80 mm rectangular profiles; optional galvanized steel weight rod insert for additional mass.
View product
Motor Hardware
Motor crown adapter sets and motor locking plates compatible with tubular motor brands across 28–60 mm motor series.
Motor Locking Plate
Stamped steel motor adapter plates with star-shaped or keyed center inserts for securing tubular motors inside roller tubes. Prevents motor rotation during operation.
View productMotor Crown Adapter
Motor crown adapter set (crown + drive wheel) sized to match 28, 35, 45, 50, and 60 mm tubular motor series to the inside diameter of standard 32–78 mm octagonal roller tubes. Glass-filled nylon or zinc die-cast construction for durability under torque.
View product
Hinges
Numbered residential and commercial sectional door hinges in galvanized steel, 4-bar window casement/awning hinges in stainless steel, BHMA A156.1 commercial mortise + residential + spring hinges, and shutter pintle hinges in cast iron / SS / bronze.
Numbered Residential Garage Door Hinge
Numbered #1 through #5 sectional door hinges in wide-body 3" and narrow-body 2¼" configurations and 14, 13, 11, 16, and 18 gauge variants. Hot-rolled galvanized steel construction, graduated to match panel position and track angle per ANSI/DASMA 102 and 116. Every production lot is inspected for hole-pattern alignment and galvanization coverage before it leaves our vetted manufacturing partner.
View productNumbered Commercial Garage Door Hinge
Numbered #1 through #10 commercial sectional door hinges in wide-body 3" 11-gauge configuration. Hot-rolled galvanized steel for door panels up to 25,000 cycle service per ANSI/DASMA 102 and 108. Hole-pattern aligned per panel position and track angle.
View product4-Bar Casement Hinge
Non-magnetic 300-series stainless steel 4-bar casement hinges in 8, 10, 10.5, 12, 12.5, 13, 14, and 16 inch lengths. Standard ~40 lb sash capacity through heavy-duty ~200 lb. Acetal or brass/nylon shoe for smooth sash travel.
View product4-Bar Awning Hinge
Stainless 4-bar awning hinges sized for awning sash 8" through 24". Standard ~82 lb and HD ~158 lb capacities. Same construction as casement variant but with different stroke geometry for top-hinged awning sash.
View productEgress 4-Bar Casement Hinge
Egress-rated 4-bar casement window hinges in 12-1/4", 12-5/16", and 16-7/16" lengths. 300-series stainless construction for life-safety code compliance. AAMA 904.1 verified.
View productCommercial Full-Mortise Hinge (Grade 1)
Grade 1 commercial full-mortise door hinge per BHMA A156.1. 4.5×4.5" or 5×5" 5-knuckle 4-ball-bearing construction in steel, brass, or 304/316 stainless. 2.5M cycle rated; NFPA 80 listed for fire-rated assemblies.
View productResidential Mortise Hinge
Residential full-mortise door hinge per BHMA A156.1 Grade 2/3. 3.5", 4", 4.5", or 5" square or radius-corner profiles in cold-rolled steel, brass, or stainless steel. Plain bearing or 2-ball-bearing variants.
View productSpring Hinge (Self-Closing)
Self-closing spring hinges per ANSI A156.17 Grade 1. 4", 4.5", or 5" sizes in steel, brass, or stainless steel. Adjustable spring tension for door weight matching. Used on fire-rated and self-closing assemblies.
View productBahama Pintle & Strap Hinge Set
Bahama shutter pintle and strap hinge sets. Strap lengths 5⅛", 7", and 8¼"; pintle offsets 0, ¾", 1¾", and 2½". Available in galvanized steel, 304/316 stainless, cast iron, solid bronze, and cast aluminum. ASTM B117 salt-spray verified for coastal service.
View productColonial Pintle / L-Hinge / Strap Set
Colonial shutter pintle, L-hinge, and strap hardware sets. Strap lengths 6"–14"; pintle offsets 0, ½", 1", 1½", 2", and 2½". Cast iron, galvanized, 304/316 stainless, bronze, and cast aluminum. TAS 201-203 verified for Ultra Hinged Colonial NOA systems.
View product
Rollers
Sectional door rollers, patio sliding door tandem rollers (residential + heavy commercial), and accordion shutter carriage wheels.
2" Sectional Door Roller
2" sectional garage door rollers in hardened steel and nylon 6/6 wheel options. 1-13/16" wheel diameter, 6200-2RS sealed bearing, zinc-plated 7/16" stem in 4" and 7" lengths. 10-ball and 13-ball ratings per ANSI/DASMA 102, 108, and 109.
View productTandem Patio Door Roller
Tandem-wheel patio sliding door roller for residential and light commercial sliding glass doors. 1-1/8" or 1-1/4" stainless steel concave wheels on ball-bearing pivots, mounted in a zinc die-cast carrier. 150 lb capacity per pair per AAMA 906.
View productHeavy-Duty Commercial Patio Door Roller
Heavy commercial tandem-wheel patio door roller for 200–500 lb sliding glass doors. 1-1/4" or 2-1/8" stainless steel concave wheels with reinforced zinc die-cast carrier and cam-adjustable height. AAMA 906 commercial-duty rated.
View productAccordion Shutter Carriage Wheel & Pivot
Accordion shutter carriage wheel and pivot hardware. #10×3″ nylon 6/6 carriage wheels (UV-stabilized); 7/8 mm hex shaft pivots in 304/316 stainless; 45° and 90° pivot variants for corner panels. Miami-Dade NOA system component.
View product
Bearings & Bearing Plates
Radial flange bearings and end + center bearing plates for garage door torsion-spring counterbalance systems. ABEC-rated, sealed, drop-in.
End Bearing Plate — Residential
Residential end bearing plate for torsion-spring counterbalance systems. 11-gauge galvanized steel with 3⅜" shaft offset and a 1" ID × 2" OD radial flange bearing. ANSI/DASMA 102 and 103 dimensional spec; 400 lb load rating at 35,000 cycles.
View productCenter Bearing Plate / Spring Anchor
Center bearing plate with integrated spring anchor for garage door torsion-shaft systems. 11-gauge galvanized steel with a flanged radial bearing for the torsion shaft. Available in slotted (SAB-450) and non-slotted (SAB-438) variants per ANSI/DASMA 102.
View productRadial Flange Bearing — 1" ID
Pre-greased radial flange bearing for garage door torsion shafts. 1" ID × 2" OD with sealed shields and a stamped retaining flange. Commercial UCF100-class variants available for higher cycle ratings. ABEC-rated for 400 lb to 1M cycles.
View product
Brackets & Fasteners
Structural mount, soffit/ceiling, angle/wedge, fascia/wall, and cable brackets in 304/316 stainless and aluminum 6061. Plus flag brackets and perforated back-hang angle for sectional door track support.
Fascia / Wall Mount Bracket
Primary structural mounting bracket for motorized retractable screen housings and awning cassettes. 3 mm 304 or 316 stainless steel, with 4×4" to 6×8" plate sizes for various screen widths and mounting surfaces. Slotted bolt holes for installation adjustment; 3/8" or M10 anchor bolts.
View productSoffit / Ceiling Mount Bracket
Under-soffit and ceiling-mount bracket for motorized retractable screen and awning installations where wall-mount isn't viable. 304 stainless or aluminum 6061 construction; 75×100 to 150×200 mm plate sizes. Powder-coat finishes for exterior installations.
View productAngle / Wedge Mount Bracket
Sloped-surface compensation bracket for motorized retractable screen and awning installations on non-vertical walls. Fixed-angle variants at 22.5° and 45°; adjustable variants spanning 5°–75°. Cast aluminum or steel with powder-coat finish.
View productCable Bracket
Wall-mount cable guide brackets for cable-guided motorized screen systems. Routes and tensions the guide cables from headbox to floor anchor.
View productSafety Mount Hardware
Safety brackets, retention clips, and tamper-resistant mounting hardware for motorized screen, shutter, and access system installations. Designed so rollers, housings, and end assemblies stay captive in high-wind events and high-cycle commercial installs.
View productFlag Bracket / Flag Angle
Universal slotted flag bracket for garage door track-radius transition. 11- to 14-gauge galvanized steel with slotted bolt holes for 10", 12", or 15" track radius accommodation. Per ANSI/DASMA 102.
View productPerforated Back-Hang Angle
14-gauge galvanized perforated angle for back-hanging garage door horizontal track. 1½×1½" and 2×2" profiles in 8 ft and 10 ft lengths. Slotted holes on 6" centers for installation adjustment. Per ANSI/DASMA 102.
View product
Window Operators
Single-arm and dual-arm casement window operators for sash 30–108 lb. E-Gard zinc die-cast bodies, hardened steel worm, and stainless arms. AAMA 904 cycle-tested.
Single-Arm Window Operator
Zinc die-cast single-arm casement window operator for sash up to 30–40 lb capacity. 9"–13½" arm lengths. E-Gard zinc die-cast body with hardened steel worm and stainless steel arm.
View productDual-Arm Window Operator
High-pressure zinc die-cast dual-arm casement window operator for sash 24"–40" wide × up to 84" tall, 96–108 lb capacity. Hardened steel worm gear; coastal stainless option for marine environments. AAMA 904 cycle test compliant.
View product
Sash Balances
Constant-force coil, block-and-tackle, and spiral-tube sash balances for single- and double-hung windows. 4–60 lb capacities.
Constant-Force Coil Balance
Constant-force coil sash balance for single- and double-hung windows. 300-series stainless steel coil with zinc die-cast cam and glass-filled PA66 shoe. Eight standard capacity ratings (3A through 10K) plus tandem (5C/5CL through 10K/10KL) for heavier sashes.
View productBlock-and-Tackle Sash Balance
Spring-loaded block-and-tackle window balance for single- and double-hung sash. 17", 20", 21", 27", 28", and 29" lengths covering 8–28 lb sash capacities. Mill-finish or zinc-plated steel U-frame with internal spring + cord + pulley assembly.
View productSpiral (Tube) Sash Balance
Spiral-tube window balance for sash 5–60 lb. 12"–48" lengths in 2" increments. Plastic or metal outer tube with internal spiral and steel spring. Tilt-pack housing for tilt-out cleaning.
View product
Locks & Latches
Window cam-action sash locks, tilt latches, accordion shutter locks (CF / HV / L / T-handle), shutter end-locks, and commercial-door strike plates + deadbolt internals + edge reinforcers. AAMA 1304 / Miami-Dade NOA / BHMA A156.5 compliant where applicable.
Cam-Action Sash Lock + Keeper
Zinc die-cast cam-action sash lock and keeper sets for single- and double-hung windows. Screw spacings 2", 2-1/16", 2-1/4", 2-1/2"; cam offsets 1/16"–3/16"; cam throws 3/8"–9/16". AAMA 1304 forced-entry rated.
View productTilt Latch (LH / RH Pair)
Tilt latch pairs for tilt-pac single- and double-hung windows. Mortise (1-1/4" hole spacing) and surface (~5" OAL) variants. Acetal, polypropylene, or glass-filled PA66 housing; stainless or zinc-plated spring.
View productAccordion Shutter Lock (CF / HV / L-Handle / T-Handle)
Accordion shutter locking mechanisms in four lever styles: CF, HV, L-handle, and T-handle. 3″×4″ die-cast zinc or aluminum body with 304 SS internals and brass cylinder. Hook deadbolt mechanism. ASTM F476 + TAS 201-203 system component.
View productCast / Stamped End Lock
Galvanized malleable iron, 304/316 stainless, or aluminum 6063 end locks for rolling shutter curtains. Sized for 2", 2-1/4", 2-1/2", and 3" steel curtains and 40–77 mm aluminum slat profiles. DASMA 108 and DASMA 115 compliant.
View productNylon End Retention Clip (Wind Lock)
Glass-filled nylon 6/6 wind-lock clips for rolling shutter slats in all standard aluminum profile heights — 37, 39, 40, 44, 55, 56, 57, 63, and 77 mm. Aluminum rivet attachment avoids galvanic corrosion against the slat. End retention is a load-path component in Miami-Dade NOA-tested systems (TAS 201 large missile, TAS 202 uniform load, TAS 203 cyclic).
View productStrike Plate (ANSI / Security)
Door latch strike plates in ANSI 4-7/8" × 1-1/4" profile, T-strike, security-extended box, and electric strike variants. Solid brass, 304 stainless, or plated zinc construction. BHMA A156.115 and A156.31 listed.
View productDeadbolt Component Set
Deadbolt internals — faceplates, strikes, reinforcers, cylinder guards, and latch tubes — sized for 1-3/4" door, 2-1/8" bore, and 5/8"×2-1/4" latch face per BHMA A156.5 / A156.36.
View productDoor Reinforcer / Edge Wrap
Stainless or galvanized steel door edge reinforcer for 1-3/4" door with 2-1/8" bore. 5/8"×2-1/4" latch face cutout. Wraps the door edge to add forced-entry resistance and prevent jamb spreading. BHMA A156.115 listed.
View product
Screen Frame Components
Aluminum screen frame extrusions, PVC screen spline (round / serrated / foam-core), and snap-in PA66 corner keys for window screen assemblies.
Aluminum Screen Frame Extrusion
Aluminum 6063-T5 screen frame extrusion in heavy-wall profiles from 5/16"×3/4" through 29/32"×7/16". 84"–144" lengths in mill, white, black, bronze, or anodized finishes. Compatible with standard PVC and foam-core screen spline.
View productWindow Screen Spline
Screen spline for retaining mesh in aluminum screen frame extrusions. Round, serrated, and foam-core variants in 0.120"–0.270" diameters; flat profiles in 5/16" and 0.344" widths. Vinyl (PVC) construction with foam-core options for tighter mesh retention.
View productWindow Screen Corner Key
Snap-in or stake-in corner keys for window screen frame extrusions. Glass-filled PA66 nylon (residential) or zinc die-cast (commercial) construction. Inside-miter and outside-miter profile-matched variants for all standard screen frame extrusions.
View product
Glazing Components
Setting blocks (EPDM / silicone / Santoprene), wedge glazing gaskets, and closed-cell EPDM glazing tape for window and storefront assemblies.
Glazing Setting Block
Setting blocks for window and patio door glazing. 4" minimum length; 1/8"–3/8" thickness; sized for 1/4"–1" glass. EPDM 80 ± 5 Shore A standard; silicone 40-80 Shore A and Santoprene 80-85 alternates for fire and acoustic glazing assemblies.
View productWedge Glazing Gasket
Wedge-shaped glazing gasket for compression-set glazing in window and storefront assemblies. EPDM 60-70 Shore A or silicone 40-80 Shore A; gap sizes 2–8 mm with reach to 6 mm. ASTM C864/C509 + GANA Glazing Manual compliant.
View productEPDM Closed-Cell Glazing Tape
Closed-cell EPDM glazing tape with acrylic PSA backing. Thicknesses 1/32"–1/8"; widths 1/4"–1". Used as glazing cushion / spacer in window and storefront assemblies. ASTM D1056 type 2A/2B and C509 verified.
View product
Spring & Counterbalance Hardware
Torsion-spring cones, winding bars, cable drums, torsion shafts, and aircraft lifting cables for sectional garage door counterbalance systems.
Torsion Spring Cone (Stationary + Winding)
Torsion-spring stationary and winding cones for residential and commercial sectional door counterbalance systems. Cast iron, ductile iron, or aluminum construction with red/black DASMA color coding per ANSI/DASMA 102 and 103. Internal IDs match standard torsion-spring sizes.
View productWinding Bar
Hardened plated steel winding bar for tensioning garage door torsion springs. Residential ½" × 18" and commercial 5/8" × 24" sizes. Hardened to resist deformation under load; plated for corrosion resistance.
View productCable Drum
Grooved cable drum for garage door torsion-spring lifting cable systems. Die-cast aluminum or steel with red/black color coding per ANSI/DASMA 102. 4" standard residential drum plus high-lift (HL) and vertical-lift (VL) variants for non-standard door configurations.
View productTorsion Shaft / Tube
Torsion shaft for sectional garage door counterbalance systems. 1" nominal Ø solid cold-rolled steel (CRS) or 1.25" OD CRS tube. Keyed or unkeyed variants per door manufacturer convention. Cut to door-width plus standard length allowances.
View productAircraft Lifting Cable Assembly
Galvanized or 304/316 stainless aircraft cable for garage door torsion-spring lifting systems. 1/8", 3/16", or 1/4" diameter with thimble + swaged stop + S-hook or loop ends. 7×7 or 7×19 cable construction per MIL-DTL-83420 and DASMA 102/103/108.
View product
Hurricane / HVHZ Shutter Hardware
Florida HVHZ (Miami-Dade NOA) hardware: aluminum guide rails, F-track / H-header storm-panel mounts. (Wind-lock clips, accordion wheels, and pintle hinges are categorized under their primary families — locks, rollers, hinges.)
Extruded Aluminum Shutter Guide Rail
Aluminum 6063-T5/T6 guide rail extrusions for rolling shutter side tracks. Profiles 41×70, 53×22, 53×60, 69×23, and 76×28 mm in 12 ft and 19 ft sticks. 31,700 PSI minimum yield. ASTM E330 / TAS 201-203 design pressure ratings.
View productF-Track / H-Header Storm Panel Hardware
Complete hurricane storm panel mounting hardware set. F-track header 146″, H-header 2″, studded angle, wing nuts ¼-20, and sidewalk bolts. Aluminum 6063-T6 + 304/316 stainless construction. Miami-Dade NOA component-grade per ASTM B117 (salt-spray) and TAS 201-203.
View product
Awning Hardware
Keder rail and matched PVC cord, cassette hood extrusions, lateral arm shoulder + elbow joint hardware, and manual-override worm gearboxes for retractable awning systems.
Aluminum Keder Rail
Aluminum keder rail in 5, 6.5, 7.5, 8.5, and 9.5 mm groove sizes for wall- and roller-tube-mounted awning fabric retention. Aluminum 6063-T5 extrusion, mill or anodized finish. Standard lengths 93″, 2.36 m, 4 m, and 6 m.
View productPVC Keder Cord
Welded PVC keder cord for awning and screen fabric retention in aluminum keder rails. 5, 6, 7, 7.5, 8, 8.5, and 9 mm core diameters with optional 20 or 30 mm welded PVC-coated polyester flap. Sized to match rail groove dimensions.
View productCassette Hood Extrusion
Aluminum full-cassette and semi-cassette hood extrusions for awning installations. Profile sizes 160×175 to 250×280 mm in lengths up to 7 m. AAMA 2604/2605 powder-coat finish. Integrated motor + idler bracket pockets.
View productAwning Arm Shoulder Bracket
Die-cast aluminum shoulder bracket for retractable awning lateral arms. Pitch adjustment 5°–75° for fabric tension and water shedding. Aluminum 6005 or 6063 with powder-coat finish.
View productAwning Arm Elbow Joint Assembly
Die-cast aluminum elbow joint for lateral-arm retractable awnings. Internal 3–5 mm stainless steel cable for tension; aluminum 6005/6063 outer construction with powder-coat finish.
View productAwning Worm Gearbox
Worm gearbox for manual awning operation and motor override. 1:7, 1:9, and 1:11 ratio variants with hardened steel worm and bronze gear. Compatible with Somfy / Simu / Becker / Nice motor override systems.
View product
Commercial Door Hardware
Nylon brush sweeps, automatic drop seals (ADB), overlapping astragals, 3-piece perimeter seal kits, intumescent smoke seals, and STC-rated acoustic seals. BHMA A156.22 Grade 1, UL 10C / 1784, NFPA 80/105 listed.
Nylon Brush Door Sweep
Type-6 nylon brush door sweep in 6063-T5 aluminum retainer. 5/8" to 1-1/2" brush trim heights; 36, 48, 72, 84, and 96" lengths. BHMA A156.22 Grade 1; UL 10C / 10B / 1784 fire- and smoke-rated; NFPA 80/105 listed.
View productAutomatic Drop Seal (ADB)
Spring-actuated automatic door bottom seal in mortise, semi-mortise, and surface-mount configurations. ½" standard drop range (¾" extended for excessive gap profiles). Aluminum case with neoprene, silicone, TPV, or brush insert. BHMA A156.22 Grade 1; UL 10C / 1784; ASTM E283/E90.
View productOverlapping Astragal
Overlapping astragal for pairs of commercial doors. 6063-T5 aluminum body with silicone, neoprene, TPV, or brush insert. 1-5/8" – 2" profile widths in 84" and 96" door-height lengths. BHMA A156.22; UL 10B/10C; NFPA 80/252 listed.
View productPerimeter Seal Kit (3-Piece)
Three-piece commercial door perimeter seal kit: one head jamb seal + two side jamb seals. Aluminum retainer with silicone, neoprene, EPDM, or brush insert. 36", 48", 84", or 96" components. BHMA A156.22; UL 10C; UL 1784 listed.
View productIntumescent Smoke Seal
Intumescent perimeter seal that expands under fire heat to seal door perimeter. PVC-cased intumescent core sized for kerf-in or surface installation. UL 1784 smoke-rated and UL 10C fire-rated; NFPA 80/105 listed.
View productSponge Silicone Acoustic Seal
Sponge silicone acoustic perimeter seal for sound-rated door assemblies. Mounted in 6063-T5 aluminum retainer; sized for STC 40 through STC 55 system ratings per ASTM E90 / E413 / E1408.
View product
Coil & Tape Products
Coil zipper tape for zip-track screens; weatherstrip rolls and gasket extrusions sold by the foot.
Sourcing standards
The operating standards behind every component family
Vetted Factories
Audited & qualified before any spec ships
Quality Inspected
Every run sample-checked before release
Warehoused in Florida
Plant City inventory for your spec
Samples Available
Verify on your bench before you commit
Direct From Manufacturer
Factory pricing without distributor stack
OEM Spec Reserved
Your dimensions, color & packaging on hand
Don't see the component family you need?
SB5 sources well beyond what's listed above. Send us a drawing, a part number, or a sample — we'll quote it, send a verification sample, and add the family to the catalog if it's a fit for the next phase.